Page 1 of 1

Safety recall M&P Shield

Posted: Tue Sep 24, 2013 7:10 pm
by Hddreamer
Got this email today thought I would pass it on to members with shields;

Smith & Wesson announced an Important Consumer Safety Alert and Inspection Procedure for all M&P Shield pistols manufactured prior to August 19, 2013. You have been identified as a purchaser of a Smith & Wesson M&P Shield pistol. This notice contains important safety information and we ask that you carefully review and follow the instructions in this notice.
 
We thank you for your cooperation and assistance in facilitating this important safety campaign,
 
Sincerely,
Smith & Wesson 
 
 
IMPORTANT CONSUMER SAFETY ALERT and INSPECTION PROCEDURE
August 22, 2013

PRODUCT:

ALL M&P Shield™ firearms manufactured before August 19, 2013.

DESCRIPTION OF THE HAZARD:

Smith & Wesson has identified a condition where the trigger bar pin could damage the lower trigger in certain M&P Shields in a way that may affect the functionality of the drop safety feature of the firearm, potentially allowing the pistol to discharge if it is dropped.
Any unintended discharge of a firearm has the potential to cause injury, and we ask that you STOP USING YOUR PISTOL IMMEDIATELY UNTIL IT HAS BEEN INSPECTED AND, IF THE CONDITION IS FOUND, REPAIRED.

DESCRIPTION OF THE PRODUCT INVOLVED: 

This Safety Alert applies to all M&P Shield pistols manufactured before August 19, 2013. We believe this condition is largely limited to recently manufactured M&P Shield pistols.  However, out of an abundance of caution, we are asking all consumers of all M&P Shields manufactured before August 19, 2013 to immediately inspect their pistols for this condition.
 
To determine whether your firearm was manufactured before August 19, 2013 please visit the MP Shield Safety Alert page.
INSPECTING YOUR PISTOL

Your firearm must be inspected to determine whether it exhibits the condition identified in this notice.  To determine whether your firearm is affected by this condition, please inspect your firearm as follows:  (Video instructions available here) 
 
Follow the procedures in your Safety & Instruction Manual to ENSURE THE FIREARM IS UNLOADED; ENSURE THAT THE MUZZLE IS POINTED IN A SAFE DIRECTION; THE SLIDE IS LOCKED BACK; AND THE MANUAL SAFETY IS ENGAGED.

Hold your pistol sideways with the muzzle pointed to the left.  Look at the trigger.  Note that the trigger is actually two pieces, with a pin in the middle that connects the two halves (Figure 1).

Look at Figure 2.  Without touching the trigger, identify the plastic tab circled in red in Figure 2.
Slowly pull the trigger.  The plastic tab encircled in Figure 2 should disappear into the upper trigger section (Figure 3).

Slowly release the trigger.  The tab should reappear as shown in Figure 2 completely on its own.

Repeat steps 4 and 5 several times.  If the small tab as shown in Figure 2 reappears each time, your pistol does not require repair.
 
If the small tab does not consistently reappear as shown in Figure 2, YOUR PISTOL MUST BE RETURNED FOR SERVICE.

 
 
 
 
 
If you are uncomfortable conducting the inspection outlined above, or are unsure whether the condition described in this notice applies to your firearm, please take your firearm to your local M&P Certified Armorer or send your firearm to Smith & Wesson for inspection.  M&P Armorers can be found on the smith-wesson.com website under Find a Dealer.
 
If after inspection it is determined that the condition outlined in this safety alert exists, the firearm must be sent to Smith & Wesson for repair.
 
REMEDY/ACTION TO BE TAKEN:

STOP USING YOUR FIREARM UNTIL IT HAS BEEN INSPECTED AND, IF THE CONDITION IS FOUND, REPAIRED. 
Your firearm must be inspected to determine whether it exhibits the condition identified in this notice.  To determine whether your firearm is affected by this condition, please inspect your firearm by following the inspection instructions above.
 
If your firearm is affected by the condition outlined in this notice, please send your pistol to Smith & Wesson.  Your firearm will be inspected, and if necessary, repaired at no cost to you. Your firearm will be returned within 5 to 7 business days.  All shipping and repair costs will be covered by Smith & Wesson.
 
Outside the United States, click HERE for a list of Authorized Warranty Centers that will repair your pistol.
CONSUMER CONTACT:

Please contact Smith & Wesson directly at 877-899-6259, or at MPShieldSafetyAlert.com to arrange for the repair, if necessary, of your pistol.
 
 
 
Smith & Wesson | 2100 Roosevelt Avenue | Springfield, MA 01104

To unsubscribe, click here.

 

Powered by MindFireInc